Kia Rio: Driveshaft and axle / Rear Hub - Carrier
Components and components location

1. Torsion beam axle
2. Rear spring
|
3. Rear drum brake disc
|

1. Torsion beam axle
2. Rear spring
|
3. Rear brake disc
|
Repair procedures
[Disc Type]
1. |
Remove the wheel and tire.
Tightening torque:
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)
|

Be careful not to damage to the wheel nuts when removing the
wheel and tire.
|
|
2. |
Remove the brake clip (A) and parking brake cable (B).


|
3. |
Remove the rear brake caliper assembly (A).
Tightening torque:
78.4 - 98.0 N·m (8.0 - 10.0 kgf·m, 57.8 - 72.3 lb·ft)
|

|
4. |
Loosen the mounting screw and the brake disc (A).
Tightening torque:
4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft)
|

|
5. |
Loosen the bolts and then remove the hub (A) from the torsion beam axle.
Tightening torque:
49.0 - 58.8 N·m (5.0 - 6.0 kgf·m, 36.1 - 43.3 lb·ft)
|

|
6. |
Install in the reverse order of removal.
|
[Drum Type]
1. |
Remove the wheel and tire.
Tightening torque:
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)
|

Be careful not to damage to the wheel nuts when removing the
wheel and tire.
|
|
2. |
Loosen the mounting screw and the brake disc (A).
Tightening torque:
4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft)
|

|
3. |
Disconnect the wheel speed sensor.

|
4. |
Loosen the hub mounting bolt and then remove the hub (A) from the torsion
beam.
Tightening torque:
49.0 - 58.8 N·m (5.0 - 6.0 kgf·m, 36.2 - 43.4 lb·ft)
|

|
5. |
Install in the reverse order of removal.
|
1. |
Check the hub for cracks and the splines for wear.
|
2. |
Check the brake disc for scoring and damage.
|
3. |
Check the rear axle carrier for cracks
|
4. |
Check the bearing for cracks or damage.
|
Components and components location
Components
[RH]
1. BJ assembly
2. Clip
3. BJ boot band
4. BJ boot
5. Dynamic damper band
6. Dynami ...
Specifications
Specification
Front Suspension
Item
Specification
Suspension type
MacPherson Strut
Shock absorb ...
Other information:
Description and operation
Description
The Seat Belt Pretensioners (BPT) are installed inside Center Pillar (LH & RH).
When a vehicle crashes with a certain degree of frontal impact, the pretensioner
seat belt helps to reduce the severity of injury to the front seat occupants by ...
Components and components location
Components
1. Shift lever knob & boots
2. Shift lever assembly
3. Shift cable assembly
Repair procedures
Removal
1.
Place the shift lever in the "N" position.
...