Kia Rio: Airbag Module / Airbag Module Disposal

Kia Rio 2017-2023 YB Service Manual / Restraint / Airbag Module / Airbag Module Disposal

Description and operation

Airbag Disposal
Special tool required

Deployment tool 0957A-34100A

Before scrapping any airbags or side airbags (including those in a whole vehicle to be scrapped), the airbags or side airbags must be deployed. If the vehicle is still within the warranty period, before deploying the airbags or side airbags, the Technical Manager must give approval and/or special instruction. Only after the airbags or side airbags have been deployed (as the result of vehicle collision, for example), can they be scrapped. If the airbags or side airbags appear intact (not deployed), treat them with extreme caution. Follow this procedure.

Deploying airbags in the vehicle

If an SRS equipped vehicle is to be entirely scrapped, its airbags or side airbags should be deployed while still in the vehicle. The airbags or side airbags should not be considered as salvageable parts and should never be installed in another vehicle.

1.

Turn the ignition switch OFF, and disconnect the battery negative terminal and wait at least three minutes.

2.

Confirm that each airbag or side airbag is securely mounted.

3.

Confirm that the special tool is functioning properly by following the check procedure.

(1)

Driver’s Airbag :

–

Remove the driver’s airbag and install the SST (0K57A-3U100A).

–

Install the driver’s airbag on the steering wheel.

(2)

Front Passenger’s Airbag :

–

Remove the glove box housing, and then disconnect the connector between the front passenger’s airbag and SRS main harness.

–

Install the SST((0K57A-3U100A).

(3)

Side Airbag :

–

Disconnect the 2P connector between the side airbag and wire harness.

–

Install the SST (0957A-2W100).

(4)

Curtain Airbag :

–

Disconnect the 2P connector between the curtain airbag and wire harness.

–

Install the SST(OK57A-3U100A).

(5)

Seat Belt Pretensioner :

–

Disconnect the 2P connector from the seat belt pretensioner.

–

Install the SST (OK57A-3U100A).

(6)

Emergency Fastening Device :

–

Disconnect the 2P connector from the anchor pretensioner.

–

Install the SST (OK57A-3U100A).

4.

Place the deployment tool at least thirty feet (10meters) away from the airbag.

5.

Connect a 12 volt battery to the tool.

6.

Push the tool’s deployment switch. The airbag should deploy (deployment is both highly audible and visible: a loud noise and rapid inflation of the bag, followed by slow deflation)

7.

Dispose of the complete airbag. No parts can be reused. Place it in a sturdy plastic bag and seal it securely.

Deploying the airbag out of the vehicle

If an intact airbag has been removed from a scrapped vehicle, or has been found defective or damage during transit, storage or service, it should be deployed as follows:

1.

Confirm that the special is functioning properly by following the check procedure on this page.

2.

Position the airbag facing up and EFD (Emergency Fastening Device) and Active Hood Actuator must be placed in piled up, at least, 5 tires, outdoors on flat ground at least thirty feet (10meters) from any obstacles or people.

3.

Connect a 12 volt battery to the tool.

4.

Push the tool’s deployment switch. The airbag should deploy (deployment is both highly audible and visible: a loud noise and rapid inflation of the bag, followed by slow deflation)

5.

Dispose of the complete airbag. No parts can be reused. Place it in a sturdy plastic bag and seal it securely.

  
–

When EFD and Active Hood Actuator are deployed, broken parts are exploded and scattered.

–

EFD and Active Hood Actuator must be placed in the piled up 5 tires to avoid exploded broken parts.

–

Technicians should wear an eye protector and extremely be cautions of exploded broken parts.

Disposal of damaged airbag

1.

If installed in a vehicle, follow the removal procedure of driver’s airbag front passenger’s and side airbag.

2.

In all cases, make a short circuit by twisting together the two airbag inflator wires.

3.

Package the airbag in exactly the same packing that the new replacement part come in.

    Description and operation Description Curtain airbags are installed inside the headliner (LH and RH) and protect the driver and passenger from danger when side crash occurs.

    Description and operation Description The Seat Belt Pretensioners (BPT) are installed inside Center Pillar (LH & RH). When a vehicle crashes with a certain degree of frontal impact, the pretensioner seat belt helps to reduce the severity of injury to the front seat occupants by retracting the seat belt webbing.

    Other information:

    Kia Rio 2017-2023 YB Service Manual: Receiver-Drier

    Repair procedures Replacement 1. Remove the condenser. 2. Remove the cap (B) on the bottom of the condenser with L wrench (A). Tightening torque : 2.7~3.2 N.m (0.28~0.

    Kia Rio 2017-2023 YB Service Manual: Cluster Ionizer (FATC only)

    Description and operation Description The cluster ionizer helps to clean up odors in the vehicle or from the air-conditioner system. When the ignition switch ON, the inoizer runs a "CLEAN" mode and then a "ION" mode, switching every about 15 minutes.

    Categories

     
    Copyright © 2025 www.krioyb.com - 0.0177